Capacitor Discharge (CD) Stud Welder - CDi 2302

Description
Unbeatable new power pack
- With efficient inverter-capacitor charging technology
- Enormous time and energy savings (30 % less energy!)
- Highest cycle sequence of its class (up to 40 studs/min.)
- 20% energy reserve due to 220 V charging voltage
- Simple operation & minimal weight (20% lighter than previous model)
- Extreme long life due to robust and functional industrial design
Highest level of quality and safety
- Capacitor formation recorded - Quality control for consistent capacitor quality through automated formation
- Shock-proof capacitor battery - No contact of the capacitors to the device housing; sparkover (short circuit) is therefore not possible!
- Cooling channel - Protects the electronic components from getting soiled. Ideal cooling of the inverter charging p.c. board for high sequence cycles.
Mild steel
Stainless steel
Aluminium
Brass
M3 to M8 (M10) - #4 to 5/16" (7/16")
| GENERAL INFORMATION |
|---|
Application
|
| ADVANTAGES |
|---|
Features
|
| TECHNICAL SPECIFICATIONS | |
|---|---|
| Welding range | #4 to 5/16" (7/16" limited), dia. 14 ga to 5/16'' (dia. 3/8" limited) (M3 to M8 (M10 limited), dia. 2 to 8 mm (dia. 10 mm limited) |
| Welding material | Mild steel, stainless steel, aluminum and brass |
| Welding rate | M3=33 studs/min. (Charging voltage 60 V) M8=12 studs/min. (Charging voltage 170 V) M10=9 studs/min. (Charging voltage 210 V) |
| Capacitance | 99,000 μF |
| Welding time | 1 to 3 ms |
| Energy | 2,400 Ws |
| Charging voltage | 50 to 220 V (stepless voltage regulation) |
| Primary power | 115 V/230 V, 50/60 Hz, 10 AT |
| Power source | Capacitor |
| Cooling type | F (temperature controlled cooling fan) |
| IP-code | IP 23 |
| Dimension L x W x H | 18.90" x 8.07" x 9.84" (480 x 205 x 250 mm) without handle |
| Weight | 37.48 lbs (17 kg) |
| Suitable Guns | See below |
| Order No | 92-13-2302B (100 V) 92-12-2302B (115 V) 92-10-2302B (230 V) |
Stud Welding Guns
C 08 with foot ring
M3 to M8 (M10) - #4 to 5/16"
- Universal design for use on flat surfaces
- All-rounder also used for welding galvanised base material
- Aluminium to M4 (#8)
C 08 with centering tube PPR-2
M3 to M8 (M10) - #4 to 5/16″
- Used for welding with templates and for protection against spatter
- All-rounder also used for welding galvanised base material
- Aluminium to M4 (#8)
CA 08 with foot ring
M3 to M8 (M10) - #4 to 5/16" (7/16")
- Universal design for use on flat surfaces
- Used to avoid rear side marking on thin sheets
- Aluminium to M6 (1/4")
- Brass to M4 (#8)
CA 08 with centering tube PPR-2/CD
M3 to M8 (M10) - #4 to 5/16" (7/16")
- Used for welding with templates and for protection against spatter
- Gap gun used to avoid rear side marking on thin sheets
- Aluminum to M6 (1/4")
- Brass to M4 (#8)




